鉅坤科技股份有限公司

規格與說明

Radio Gateway Series

 無線電閘道器

硬體規格 :

可整合無線電Radio介面卡/FXS/FXO/T1/E1

本主機需搭配CPU控制卡:

• CPU：ATOM N2930
• 記憶體：DDRII 4GB
• 網路端 口：10/100/1000 LAN ,
• 硬碟容 量：120G 
• USB 2.0 Port：2 (Front)
• 工作溫度：0 - 40°C
• 工作溼度：8% to 90% (non-condensing)

語音規格

• 符合SIP RFC 3261 / H.323 規範(ITU-T) 通信協定
• 語音壓縮規格: G.711,G.722,G.723,G.726,G.729,GSM,Slin,Lpc10,Speex

自動總機

• Web 介面自動總機語音流程編輯
• 特定時間宣告語
• 假日工作時間設定
• 支援多國語言

交換機ISDN鍵結

• Toshiba,NEC,Alcatel,Avaya,phillips...等

語音郵箱

• 支援多國語言
• SIP留言指示
• 電子郵件通知
• 可由Web存取語音留言
• 可由電話聽取語音留言

會議功能

• 隨取建立會議室
• 個人虛擬會議室
• 會議事件提示音
• 單一會議室最多可容納32名成員
• 可由網路電話登入

加強功能

• 多應用IVR(語音互動系統) 資料庫
• 可支援SIP/H323/MGCP/G-Talk/OCS/Skype 鍵結

精選電話功能

• 通話轉接Transfer
• 來電轉送Forward
• 來電轉送通知Forwarded Notice
• 撥號限制Call Screening
• 去電顯號設定Caller ID Privacy
• 來電等候Call Waiting
• 通話保留Call Hold
• 來電代接Call Pickup (Global, Group)
• 指定代接Specified Call Pickup
• 電話跟隨Follow Me
• 勿打擾Do Not Disturb
• 去電顯示替換ANI Replacement
• 回撥Call Return
• 隱藏或顯示主叫號碼Hide /Show ANI Selection
• 通話駐留與取回Call Park/Retrieve
• 分機註冊Extension mobility

●忙線自動回覆 busy call

規格與說明

T-288C/NC  Leased Line Modem

SPECIFICATIONS

Compatibility

V.34+ 33.6/31.2Kbps 4DTCM

V.34 28.8/26.4/24/21.6/19.2/16.8/14.4/ 12/9.6/7.2/

4.8/2.4Kbps 4DTCM

V.33 14400/12000/9600/7200bps TCM, 4800bps QAM

V.32bis 14400/12000/7200bps TCM

V.32 9600bps TCM, 9600/4800bps QAM

V.29 9600/7200bps QAM, 4800bps DPSK

V.27bis 4800/2400bps DPSK

V.26 2400/1200bps DPSK

V.22bis 2400bps QAM

V.22/Bell 212A 1200bps DPSK

V.23 1200/75, 600/75bps FSK

V.21/Bell 103 300bps FSK

Data Format

Synchronous or Asynchronous

Total bit length: 8, 9, 10, 11

Data Speed

Asynchronous

75/300/600/1200/2400/4800/7200/9600/12000/

14400/16800/19200/21600/24000/26400/28800/

31200/33600/38400/57600/76800/115200bps

Synchronous

1200/2400/4800/7200/9600/12000/14400/16800/

19200/21600/24000/26400/28800/31200/33600bps

DTE Interface

EIA RS-232C, ITU-T V.24/V.28

Line Requirement

Dial line, 2/4 wire leased line

Transmit Level

Dial line: 0 to -15dBm for where allowed, or fixed -10dBm

Leased line: -6 to -31dBm for V.34

0 to -31dBm for other V-series

Receive Dynamic Range

+3 to -26, +3 to -40, -6 to -33, -6 to -43dBm

Equalization

Automatic adaptive EQ

Compromise EQ: M1040 or cable

Call Progress Monitoring

Dial tone, Ring, Ringback, Busy and Backup dial

Line Status Monitoring

TX level, RX level, S/N ratio, Delay, Freq. offset, Far-end

echo freq. offset, Near-end echo, Far-end echo, Retrain

count, Tx Baud Rate, Rx Baud Rate, Tx Carrier, Rx Carrier,

Tx Power Back-off level

Memory

A nonvolatile memory for storing 10 sets of user profile and

10 telephone numbers with 20 characters, the 10 sets of

factory default are stored in ROM

Line Interface

RJ-11 for Dial Line, JM8 for Leased Line

Transmit Clock

Internal, Loopback, External clock

Dialing Command

Extended AT and V.25bis command set

Dialing Type

Tone/Pulse dialing

Flow Control

RTS/CTS, XON/XOFF, CTS only, ENQ/ACK

Power

AC Source: 90 ∼ 265V, Autorange, 47 ∼ 63 Hz

DC Source: -36 ∼ -72V for rack option

Dual redundant power unit for rack option

規格與說明

T-336Cx/Nx/NDx  Leased Line Modem

Specification

Compatibility

• 34+: 33.6/31.2 Kbps SM (4D TCM)
• 34: 28.8/26.4/24/21.6/19.2/16.8/14.4/12/9.6/7.2/4.8/2.4 Kbps SM(4D TCM)
• 32bis: 14400/12000/7200 bps TCM
• 32: 9600 bps TCM, 9600/4800 bps QAM
• 22bis: 2400 bps QAM, 1200 bps BPSK
• 22/Bell 212A: 1200 bps DPSK
• 23: 1200/75, 600/75 bps FSK
• 21/Bell 103: 300 bps FSK

Data Format

• Synchronous or Asynchronous
• Total bit length: 8, 9, 10, 11

Data Speed

• Asynchronous-

75/300/600/1200/2400/4800/7200/12000/14400/16800/19200/21600/
24000/26400/28800/31200/33600/38400/57600/76800/115200 bps

• Synchronous-

1200/2400/4800/7200/9600/12000/14400/16800/19200/21600/
24000/26400/28800/31200/33600 bps

• Total bit length : 8, 9, 10, 11 bits
• Parity bit : odd, even, none
• Stop bit : 1, 1.5, 2 bits

Line Interface

• Cx/Nx: RJ-11 for dial-up, JM8 (like RJ45) for leased line
• NDx: 6-pin Terminal Block or 50-pin Centronic

DTE Interface

• EIA RS-232C, ITU-T V.24/V.28
• Line Requirement
• Dial-up line, 2/4-wire leased line
• Transmit Level
• Dial-up line: 0 to -15 dBm; Leased line: 0 to -31 dBm
• Receive Dynamic Range
• -4 to -43 / 0 to -33 dBm
• Equalization
• Automatic adaptive EQ
• Call Progress Monitoring
• Dial tone, Ring, Ring-back, Busy and backup dial
• Dialing Command and Type
• Extended AT and V.25bis using Tone/Pulse/Mixed
• Clock Source
• Internal/External/Loopback
• Flow Control
• RTS/CTS, XON/XOFF, CTS only
• Diagnostics

Test Features

• 54/V.52 , LAL/DL/RDL
• Test Patterns – 511

Line Status Monitoring

• Tx level, Rx level, S/N ratio, EQM value, delay, phase jitter, freq. offset, far-end freq. offset, far-end echo, DTE format, retrain count, Tx baud rate, Rx baud rate, Tx carrier, Rx carrier, Tx speed, Rx speed, Tx power back-off level, Interface lead monitoring

Power Requirement

• Input
• AC: 90 ~ 265 V, Auto-range, 47 ~ 63 Hz
• DC: -36 ~ -72 V (optional)
• Dual redundant power unit for rack (optional)

Power Consumption

• < 5W

Environment Temperature

• Operating Temperature : 0 °C ~ 50 °C
• Storage Temperature : -25 °C ~ 70 °C

Humidity

• Up to 95% non-condensing

規格與說明

P-MUX Solution Series
EMux-400 (2/4 E1)

Multi-E1 over IP

Evolutionary Convergence in Transmission of real-time Voice/Video and Data over Ethernet Network

Product Overview

EMux-400 is designed as a multi-service access platform for E1 over IP applications. E1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support E1 (ITU-T G.823) Jitter performance.

Cost-effective LAN Deployment
(PDH over Ethernet)

EMux-400 provides cost-effective applications of traditional circuit-switched system over IP. With EMux-400, it is easy to interconnect with the existing E1 systems over IP that are used to carry data, voice and video.

Transparent Transmission

EMux-400 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of EMux-400 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 4 x E1 (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3

Ethernet Interface

WAN Port: 100 Base-TX Ethernet

Interface: RJ-45

 LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

RS-232 console port (Craft Terminal) 

規格與說明

IP-MUX Solution Series
EMux-400 (2/4 T1)

Multi-T1 over IP

Evolutionary Convergence in Transmission of real-time Voice/Video and Data over Ethernet Network

Product Overview

EMux-400 is designed as a multi-service access platform for T1 over IP applications. T1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support T1 (ITU-T G.824) Jitter performance.

Cost-effective LAN Deployment
(PDH over Ethernet)

EMux-400 provides cost-effective applications of traditional circuit-switched system over IP. With EMux-400, it is easy to interconnect with the existing T1 systems over IP that are used to carry data, voice and video.

Transparent Transmission

EMux-400 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of EMux-400 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 4 x T1 (ITU-T G.703)
Interface: RJ-48c (100 Ohm)
Line Coding: B8ZS

Ethernet Interface

WAN Port: 100 Base-TX Ethernet

Interface: RJ-45

LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

RS-232 console port (Craft Terminal) 

規格與說明

Product Overview

Your LAN or high speed traffic may exceed  1.5 Mbps, yet not justify the cost of an STM-1/OC-3 pipe. IME-800 inverse multiplexer bridges the gap between T1 and Ethernet, cost-effectively transports your LAN or high speed data traffic across multiple, stable, and robust TDM links.

Cost-Effective LAN Extension (LAN over WAN)

As broadband communications increases, so does the need for higher WAN bandwidth (above T1 data rate). However, STM-1/OC-3 pipes are still very expensive. Moreover, they are not always readily available, and are often overkill for the traffic capacity.

IME-800 transfers Ethernet packets transparently, enabling service providers to use their next generation equipment in TDM environment. The pure Ethernet payload carried by IME-800 eliminates the need to invest in conversion equipment between Ethernet/IP and TDM, e.g. Router and CSU/DSU.

Specification

Line Interface

Port: up to 4 x T1  (ANSI T.102) Interface: RJ-48c (100 Ohm)
Line Coding: B8ZS or AMI

Ethernet Interface (LAN)

Port: 100 Base-TX Ethernet
Interface: RJ-45

Dimensions (H x W x D)

 44 x 320 x 125 (mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% non condensing

Configuration and Management

RS-232 console port (Craft Terminal)

規格與說明

Ethernet over 1/2/4E1 Inverse Multiplexer

Bridge the Gap between E1 and Ethernet with TDM Inverse Multiplexing

Product Overview

Your LAN or high speed traffic may exceed 2 Mbps, yet not justify the cost of an STM-1/OC-3 pipe. IME-800 inverse multiplexer bridges the gap between E1 and Ethernet, cost-effectively transports your LAN or high speed data traffic across multiple, stable, and robust TDM links.

Cost-Effective LAN Extension (LAN over WAN)

As broadband communications increases, so does the need for higher WAN bandwidth (above E1 data rate). However, STM-1/OC-3 pipes are still very expensive. Moreover, they are not always readily available, and are often overkill for the traffic capacity.

IME-800 transfers Ethernet packets transparently, enabling service providers to use their next generation equipment in TDM environment. The pure Ethernet payload carried by IME-800 eliminates the need to invest in conversion equipment between Ethernet/IP and TDM, e.g. Router and CSU/DSU.

Product Overview

Your LAN or high speed traffic may exceed 2 Mbps, yet not justify the cost of an STM-1/OC-3 pipe. IME-800 inverse multiplexer bridges the gap between E1 and Ethernet, cost-effectively transports your LAN or high speed data traffic across multiple, stable, and robust TDM links.

Cost-Effective LAN Extension (LAN over WAN)

As broadband communications increases, so does the need for higher WAN bandwidth (above E1 data rate). However, STM-1/OC-3 pipes are still very expensive. Moreover, they are not always readily available, and are often overkill for the traffic capacity.

IME-800 transfers Ethernet packets transparently, enabling service providers to use their next generation equipment in TDM environment. The pure Ethernet payload carried by IME-800 eliminates the need to invest in conversion equipment between Ethernet/IP and TDM, e.g. Router and CSU/DSU

 Specification

Line Interface

Port: up to 4 x E1 (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3

Ethernet Interface (WAN port)

Port: 100 Base-TX Ethernet
Interface: RJ-45

Dimensions (H x W x D)

 44 x 320 x 125 (mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                              

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% non condensing

Configuration and Management

RS-232 console port (Craft Terminal) 

規格與說明

ProFOM-1600(4E1 or 4T1)
Fiber Optical Multiplexer(Single-mode or Multi-mode)

ProFOM-1600 is designed as a multi-service access platform for E1 (or T1)over Fiber applications. E1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support E1 (ITU-T G.823) Jitter performance.

Cost-effective LAN Deployment
(PDH over fiber Optical)

ProFOM-1600 provides cost-effective applications of traditional circuit-switched system over fiber. With ProFOM-1600, it is easy to interconnect with the existing E1 systems over fiber that are used to carry data, voice and video.

Transparent Transmission

ProFOM-1600 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of ProFOM-1600 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 4 x E1 or 4x T1  (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3 (E1) , B8ZS(T1)

Fiber Optical  Interface

WAN Port: 1 x 100Base-FX SFP slot

Connector: SFP  LC Type

Rate: 100Mbps

Ethernet Interface

LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

規格與說明

ProFOM-1600(2E1 or 2T1)

Fiber Optical Multiplexer(single-mode or Multi-mode)

ProFOM-1600 is designed as a multi-service access platform for E1 (or T1)over Fiber applications. E1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support E1 (ITU-T G.823) Jitter performance.

Cost-effective LAN Deployment
(PDH over fiber Optical)

ProFOM-1600 provides cost-effective applications of traditional circuit-switched system over fiber. With ProFOM-1600, it is easy to interconnect with the existing E1 systems over fiber that are used to carry data, voice and video.

Transparent Transmission

ProFOM-1600 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of ProFOM-1600 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 2x E1 or 2x T1 (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3(E1) or B8ZS(T1)

Fiber Optical  Interface

WAN Port: 1 x 100Base-FX SFP slot

Connector: SFP  LC Type

Rate: 100Mbps

Ethernet Interface

LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

RS-232 console port (Craft Terminal) or Telnet

規格與說明

OTN-100G

OTN-100G (Optical Transport Network) is a Wire Optical Transport Devices.   Not only stanard  product cargo with 100G optical line port & 10x10Gbps optical Etherent client ports,  but also extendable as chassis-type with “pluggable 100G Transponder/Muxponder special ports creation. Let user interface  meet to the customized requirement to include various 100G interface conversion. For management part, engineering CLI (RS-232) & simple Etherent(RJ-45) port are provided & system can be configured as Web browser/SNMP/MIB w/ SDN-controlling capability.  Network application topology would  be a simple  100G ports “converter”, “point-to-point link ”, “dual path protection”, or “flexible  ring” various network application design

 With an 100G uplink to all optical network field, this device can provide “5G/4G fronthaul/midhaul”, “GPON backhaul”, “GigaAccess backhaul” services and “bridging various cloud Datacenter/Edge optical ports with the required 100G/10G traffic link extension. This standard box is  “100G OTN/10x10G Ethernet” & can be flexible for other client interface  by proper effort involved.  Due to more rapid growthing  at  “5G mobile Network/B5G-6G-Satellite”, “all optical Fixed Network” & “Cloud Data Center” migrating trend, network equipment need 100Gbps-base high bandwidth to support. This  100G-OTN is a highly compacted box for mobile network/Video/AR/VR/AI application by proper transponder/muxponder service traffic into OTN(OTU4) frame structure.  Let network system can more flexibly meet new service applications by 100G-base huge bandwidth deployment

l  Smoothly merge the TDM & Ethernet/IP traffic ports  into All-Photonics Network  world : To meet IOWN (Innovative Optical & Wirelesss Network) service developing requirement

l  Scalability in Ethernet service : The Ethernet service is scalable to fit sites request by design-in 100Gbps and client-side can be from one 10Gbps to multiple 10Gbps as easier bandwidth expansion.

l  Versatile Network Management System : To provide a Craft Interface and easy-to-use Network Mangemant (SNMP-base), there is also MIB sets for customized facilities to get integratable O&M &  to be  viewed at  both remote and central side.

Specification

規格與說明

2 Slot IPPBX

• 尺 寸 (cm) ：4.5(H) x 44(W) x 30(D)
  ●CPU：ATOM D525
  ●記 憶 體：DDRII 4GB
  ●網 路 端 口：10/100/1000 LAN x2,
  ●硬 碟 容 量：500G 
  ●USB 2.0 Port：2 (Front)
  ●FXO/S：4 Port
  ●電 源：80W External 110VAC /220VAC Adapter
  ●工作溫度：0 - 40°C
  ●工作溼度：8% to 90% (non-condensing)

語音規格
●符合SIP RFC 3261 / H-323 規範(ITU-T) 通信協定
●語音壓縮規格: G.711,G.722,G.723,G.726,G.729,GSM,Slin,Lpc10,Speex
自動總機
●Web 介面自動總機語音流程編輯
●特定時間宣告語
●假日工作時間設定
●支援多國語言
交換機ISDN鍵結
●Toshiba,NEC,Alcatel,Avaya,phillips...等
語音郵箱
●支援多國語言
●SIP留言指示
●電子郵件通知
●可由Web存取語音留言
●可由電話聽取語音留言
會議功能
●隨取建立會議室
●個人虛擬會議室
●會議事件提示音
●單一會議室最多可容納32名成員
●可由網路電話登入
加強功能
●多應用IVR(語音互動系統) 資料庫
●可支援 SIP/H323/MGCP/G-Talk/OCS/Skype 鍵結
精選電話功能
●通話轉接 Transfer
●來電轉送 Forward
●來電轉送通知 Forwarded Notice
●撥號限制 Call Screening
●去電顯號設定 Caller ID Privacy
●來電等候 Call Waiting
●通話保留 Call Hold
●來電代接 Call Pickup (Global, Group)
●指定代接 Specified Call Pickup
●電話跟隨 Follow Me
●勿打擾 Do Not Disturb
●去電顯示替換 ANI Replacement
●回撥 Call Return
●隱藏或顯示主叫號碼 Hide /Show ANI Selection
●通話駐留與取回 Call Park/Retrieve
●分機註冊 Extension mobility
●忙線自動回覆 busy call back

規格與說明

xDSL/GPON/CWDM Series